168F / 170F / 188F / 190F (5.5HP–18HP) Gasoline Engine Sourcing & PTO Crankshaft Selection Guide
Share to WeChat Moments

When OEM machinery manufacturers, agricultural distributors, and construction rental fleets import horizontal-shaft 4-stroke OHV gasoline engines (5.5HP to 18HP), 90% of assembly line delays are caused not by engine performance, but by mismatched Power Take-Off (PTO) crankshaft dimensions. A 19.05 mm (3/4") imperial Q-shaft and a 20.00 mm metric S-shaft look virtually identical to the naked eye—yet that 0.95 mm discrepancy makes it impossible to press on a high-pressure washer hollow-shaft pump or belt clutch.
In this OEM sourcing and engineering guide, Ningde Kinger Electrical Machinery CO.,LTD. (SUPERKIGER) documents the complete 5.5HP–18HP (168F / 170F / 177F / 188F / 190F / 192F) specification matrix and the 5 standardized PTO crankshaft profiles (Q, S, T, V, R) so your procurement team can specify exact drop-in engines every time.

1. Master Specification Matrix: 5.5HP–18HP (168F to 192F) OHV Gasoline Engines
All SUPERKIGER industrial gasoline engines feature cast-iron cylinder liners, forged steel crankshafts, dual ball-bearing crankcase support, T.C.I. contactless transistorized ignition, and automatic Low-Oil Alert protection. They are divided into two universal chassis footprints: Small-Block (163cc – 236cc) and Big-Block (270cc – 486cc).
| SUPERKIGER Model | Industry Engine Code | Max Power @ 3600 RPM | Bore × Stroke (mm) | Displacement | Compression | Tank / Oil Cap. | Specific Fuel Burn | Net Weight | Dimensions (L×W×H mm) |
|---|---|---|---|---|---|---|---|---|---|
| KG160 | 168F-1 (GX160 Class) | 5.5 HP | 68 × 45 mm | 163 cc | 8.5 : 1 | 3.6 L / 0.6 L | 290 g/HP·h | 12.5 kg | 370 × 310 × 360 |
| KG200 | 168F-2 (GX200 Class) | 6.5 HP | 68 × 54 mm | 196 cc | 8.5 : 1 | 3.6 L / 0.6 L | 290 g/HP·h | 13.0 kg | 370 × 310 × 360 |
| KG210 | 170F (High-Torque) | 7.0 HP | 70 × 55 mm | 212 cc | 8.5 : 1 | 3.6 L / 0.6 L | 290 g/HP·h | 13.3 kg | 370 × 310 × 360 |
| KG236 | 172F (Compact 8HP) | 8.0 HP | 72 × 58 mm | 236 cc | 8.5 : 1 | 3.6 L / 0.6 L | 290 g/HP·h | 14.5 kg | 370 × 310 × 360 |
| KG270 | 177F (GX270 Class) | 9.0 HP | 77 × 58 mm | 270 cc | 8.0 : 1 | 6.0 L / 1.1 L | 290 g/HP·h | 28.0 kg | 520 × 420 × 480 |
| KG390 | 188F (GX390 Class) | 13.0 HP | 88 × 64 mm | 389 cc | 8.0 : 1 | 6.0 L / 1.1 L | 290 g/HP·h | 29.0 kg | 520 × 420 × 480 |
| KG420 | 190F (Heavy-Duty) | 15.0 HP | 90 × 66 mm | 418 cc | 8.0 : 1 | 6.0 L / 1.1 L | 290 g/HP·h | 28.5 kg | 520 × 420 × 480 |
| KG490 | 192F (Max Single-Cyl) | 18.0 HP | 94 × 70 mm | 486 cc | 8.0 : 1 | 6.0 L / 1.1 L | 290 g/HP·h | 30.0 kg | 520 × 420 × 480 |
Why Upgraded 212cc (KG210) and 418cc (KG420) Models Are Replacing Standard 163cc and 389cc Units
Because the KG210 (170F, 7.0HP) uses the exact same 370 × 310 × 360 mm exterior footprint and 13.3 kg weight class as the KG160 (5.5HP), OEM manufacturers can upgrade their plate compactors, power trowels, and tillers from 5.5HP to 7.0HP without changing a single mounting hole on their steel chassis. Likewise, the KG420 (190F, 15HP) and KG490 (192F, 18HP) drop directly onto any KG390 (188F, 13HP) frame.
2. PTO Crankshaft Selection Guide: Q-Shaft vs. S-Shaft vs. T-Shaft vs. V-Shaft vs. R-Shaft
Viewing the PTO shaft end-on (from the output side opposite the recoil starter), all standard SUPERKIGER horizontal engines rotate counter-clockwise (CCW). Before placing a container order, verify which of the five crankshaft profiles matches your driven coupling:
| Shaft Code | Mechanical Geometry | Small-Block (168F / 170F) Spec | Big-Block (188F / 190F / 192F) Spec | Target OEM Machinery Applications |
|---|---|---|---|---|
| Q-Shaft (Inch Keyed) | Straight cylindrical shaft with rectangular keyway + UNF tapped center hole | Ø 19.05 mm (3/4") × 58–61.5 mm length, 4.78 mm (3/16") keyway | Ø 25.40 mm (1.0") × 72–88.5 mm length, 6.35 mm (1/4") keyway | Direct-drive triplex high-pressure washers, North American log splitters, go-karts, lawn edgers |
| S-Shaft (Metric Keyed) | Straight cylindrical metric shaft with parallel keyway + M8 tapped center hole | Ø 20.00 mm × 50–58 mm length, 5.0 mm keyway | Ø 25.00 mm × 60–72 mm length, 7.0 mm keyway | V-belt pulleys, vibrating plate compactors, concrete power trowels, power tillers, air compressors |
| T-Shaft (Threaded Pump) | Stepped cylindrical shaft with external male threads + keyway shoulder | Ø 19.05 mm / 20 mm with 5/8"-18 UNF or M18×1.5 external thread | Ø 25.00 mm / 25.4 mm with M20×1.5 or 1"-14 UNS external thread | Direct-coupled centrifugal water pumps (WP20 / WP30 / WP40) and chemical pumps where the impeller screws directly onto the crank |
| V-Shaft (Tapered Generator) | Precision conical taper (no keyway; torque transmitted via taper friction lock + central drawbolt) | Standard J609B Taper (1:5 or 3/16" per foot taper), Ø 19.95–22.16 mm | Heavy Generator Taper, Ø 25.4–28.5 mm conical journal | Synchronous AC alternator rotors on portable gasoline generators (KG2500 / KG3500 / KG6500E) |
| R-Shaft (2:1 Gear / Chain Reduction) | Integrated oil-bath secondary reduction gearbox bolted to crankcase cover | 1,800 RPM Output (1:2 reduction), Ø 20 mm or Ø 22 mm keyed shaft | 1,800 RPM Output (1:2 reduction, optional centrifugal wet clutch), Ø 25 mm shaft | High-torque low-speed cement mixers, agricultural rotavators, marine long-tail mud motors, winches |
3. Critical Engineering Checks Before Ordering OEM Replacement Engines
- **Never Confuse
19.05 mm (3/4" Q-Shaft)with20.00 mm (S-Shaft): ** Always measure your existing pulley or pump bore with a digital Vernier caliper—not a tape measure. If you are building hollow-shaft triplex plunger pressure washers (3000–4000 PSI), specify Q-Shaft (19.05 mmon 7HP /25.4 mmon 13HP–15HP). - Air Cleaner Configuration for Dusty Environments: For concrete saws, plate compactors, and agricultural tillers, order our Half-Dry Oil-Immersed Foam Air Filter or Dual-Stage Cyclone Snorkel Air Cleaner to prevent silica dust ingestion.
- Crankcase Oil & Fuel Consumption Planning: All
168F/170Fblocks require 0.60 L of SAE 10W-30 / 15W-40 oil, while177F/188F/190F/192Fblocks require 1.10 L. For complete lubrication and fuel calculation tables, consult our 4-Stroke Engine Oil Viscosity & Capacity Guide and 1kW–12kW Generator & Engine BSFC Fuel Consumption Chart. - When to Switch to Direct-Injection Diesel (
KG186FA/KG1100F): If your machinery operates more than 4–6 hours daily on diesel-standardized construction sites, compare our KG186FA (418cc, 6.5kW) and KG1100F (660cc, 9.8kW) in the Diesel Engine Catalog.
Request CAD Shaft Drawings & Factory Container Pricing
Whether you are sourcing 20FT / 40HQ container loads of bare engines for local machinery assembly or custom OEM color/branding packages, contact the SUPERKIGER engineering team or browse our complete 4-Stroke Gasoline Engines and Generator & Engine Spare Parts catalogs.
Frequently Asked Questions
What is the difference between a 168F-1 (5.5HP), 168F-2 (6.5HP), and 170F (7.0HP) gasoline engine?
All three share the identical 162mm × 75mm base mounting bolt pattern and external chassis dimensions (370 × 310 × 360 mm), making them 100% drop-in interchangeable on machinery frames. The difference lies in cylinder bore and crankshaft stroke: 168F-1 (KG160, 5.5HP) uses a 68×45mm bore/stroke (163cc); 168F-2 (KG200, 6.5HP) lengthens the stroke to 68×54mm (196cc); and 170F (KG210, 7.0HP) enlarges both bore and stroke to 70×55mm (212cc) for higher low-end torque.
Which PTO crankshaft type (Q, S, T, V, or R) do I need for a water pump, pressure washer, or generator?
Match the PTO (Power Take-Off) shaft strictly to the driven machine: Q-Shaft (3/4-inch / 19.05mm or 1-inch / 25.4mm straight keyed shaft) fits North American pressure washers, plate compactors, tillers, and go-karts; S-Shaft (20mm or 25mm metric straight keyed shaft) fits European/Asian belt pulleys and construction machinery; T-Shaft (external threaded shaft) threads directly into centrifugal water pump impellers (WP20/WP30); V-Shaft (tapered conical shaft) locks directly into generator rotors; and R-Shaft provides a 2:1 chain/gear reduction (1,800 RPM output) for cement mixers and heavy agricultural tillers.
Are SUPERKIGER KG160, KG200, and KG390 engines bolt-for-bolt compatible with GX160, GX200, and GX390 frames?
Yes. The SUPERKIGER KG160 (163cc), KG200 (196cc), and KG210 (212cc) match the standard GX160/GX200 base mounting footprint and PTO centerline height. Similarly, our big-block KG270 (270cc), KG390 (389cc), KG420 (418cc), and KG490 (486cc) match the standard GX270/GX390 industrial mounting pattern (195mm × 96–108mm slotted base).
How do you prevent ordering the wrong PTO shaft when importing bulk container loads of engines?
Always specify four engineering parameters on your Purchase Order (PO): (1) Shaft profile code (Q, S, T, V, or R), (2) Exact outside diameter in millimeters or inches (e.g., 19.05mm vs. 20.00mm—a 0.95mm difference will prevent pulley installation!), (3) Keyway width and usable shaft length, and (4) Central internal thread standard (5/16-24 UNF vs. M8×1.25 metric).